2766160103 - 6H3F(30HP,460/380,6/5,W)
The 6-inch High-Temp Motor utilizes a distinctive premium encapsulation process and water-soluble coolant to allow dependable, continuous operation in 6" diameter or larger water wells with water temperatures up to 90 ºC (provided minimum allowable flow rates past the motor are maintained). This submersible motor is powered by design and can handle thrust loads 25% higher than a standard motor without oil. Its superior construction comes with water-lubricated radial and thrust bearings to benefit from a maintenance-free operation.
Sample image - may not be representative of product features
2766160103 - 6H3F(30HP,460/380,6/5,W)
The 6-inch High-Temp Motor utilizes a distinctive premium encapsulation process and water-soluble coolant to allow dependable, continuous operation in 6" diameter or larger water wells with water temperatures up to 90 ºC (provided minimum allowable flow rates past the motor are maintained). This submersible motor is powered by design and can handle thrust loads 25% higher than a standard motor without oil. Its superior construction comes with water-lubricated radial and thrust bearings to benefit from a maintenance-free operation.
Item
Model:
Ratings
| HP | 30 hp |
| Frequency | 50Hz/60Hz |
| Phases | Three-Phase |
| Amps – Full Load | 41.3 A |
| Amps – Service Factor | 47.2 A |
| Volts | 380 VAC / 460 VAC |
| Voltage Tolerance (%) | -10.0% / +10.0% |
| Wire | 3-Wire |
| Motor Connection | DOL |
| Thrust Bearing Rating | 10000 lb |
| Lead Length | 13 ft |
| Motor | Encapsulated |
| Continuous Duty | Yes |
| Efficiency Service Factor Load [%] | 83.00 % |
| Protection [IP] | IP68 |
| Lead Wire Size | AWG #8 |
| Lead Retainer Method | Lead Jam Nut |
| Motor Insulation Classification | F |
| Poles | 2 |
| S.F. | 1.15 |
| Motor Cooling | Water |
| Minimum Cooling Flow | .50 ft/sec |
| Motor Ambient Temperature Rating Nominal | 194 °F |
| Thrust Bearing Rating | 10000 lb |
| Motor Adapter | Double flange |
| Rotation | Counter clockwise facing the shaft |
| SubTrol Heat Sensor | No |
| Winding Resistance (Main Winding) | .52-.64 |
Materials of Construction
| Motor Shaft End – Material | 17-4SS |
| Thrust Bearing | Kingsbury Type |
| Seal Material | Silicon Carbide / Silicon Carbide |
| Seal | Mechanical Seal |
| Lead Insulation Material | Overmolded |
| Diaphragm Material | FKM |
| Motor Bottom End Bell Material | Cast Iron with E-Coat Paint |
| Motor Fill Solution (Water Soluble / Non Toxic) | Yes |
| Motor Fill Solution | FES92 |
| Motor Top End Bell Material | Cast Iron with E-Coat Paint |
| Shaft Slinger Material | Nitrile Rubber (NBR) |
| Stator Ends Material | Carbon Steel |
| Stator Fill | Resin |
| Stator/ Motor Shell Material | 300 Series SS |
| Winding Material | Copper |
Dimensions
| Motor Diameter – Physical Diameter | 5.44″ |
| Motor Length | 38.6 “ |
| Product Weight | 162 lb |
| Product Weight with Pack | 176 lb |
| Carton Length | 42.25 “ |
| Carton Width | 7.25 “ |
| Carton Height | 10.5 “ |
| Shaft Diameter | 1 “ |
| Shaft End | Spline |
Other
| Warranty Standard Time | 12 Mo. from Date of Install / 24 Mo. from Date of Manufacturing |
| Repair Kit Available | Yes |
Ready to working with us?
Please fill in the following form. You will be contacted as soon as possible.